Airsoft Press eBook Manual
- Thorough Indepth Review on Airsoft AEG Rifle Upgrades
- Step by Step Illustrated directions and tutorials
- Perfect for Novice or Advanced Airsofters
- A Must have for any player of the Airsoft Sport
- Addresses CYMA, Well, Both Elephant, and other varieties of Airsoft LPEG Guns
- Contains over 60 Pages of Illustrations and Guides
- Click on More Info for Table of Contents

Table of Contents

Tools you’re going to need
Proper handling of the screws
The proper ways of taking things apart and putting them back together
Your Upgrade Objectives
Types of LPEG

<< High FPS Upgrade >>

What are the key elements of a high FPS setup?
FPS increase in meter readings VS performance increase in a practical sense: the law of diminishing marginal gain in performance.
BB bullets: the heavier the better?
Does FPS always go hand in hand with Joule?
What is the difference between the FPS system and the Joule system?
How do you use FPS to measure Joule?
How do you use FPS to give an estimate of the range?
Higher FPS = lower ROF?
Softer spring = Higher ROF?
Harder spring = Lower ROF?
Is 8.4V insufficient for an upgraded mechbox?
Does battery size matter?
Longer spring versus shorter spring: the longer the better?
What are the major parameters of a spring?
Is a harder spring more harmful for the internals?
Installing a long spring: tricks and potential danger.
Installing a short spring: tricks and potential danger.
Why (and why not) should the spring beground?
How to facilitate spring spinning?
What is a variable pitch spring? Is it always better for LPEG?
Use of spacers for spring compression: tricks and potential danger.
What is wrong with a custom made spring?
Systema Springs versus PDI Springs (for Type I LPEG)
Can stainless steel spring offer better FPS?
Can Telfon Coated spring offer better FPS?
What motor do most Type II/III LPEGs use?
Why (and why not) should I use a Bore-Up Cylinder?
Different guns use different cylinders that have different number and position of openings. Why’s that?
Is it useful to block the cylinder opening altogether?
Why is it useful to put holes on the piston head? Any alternative?
Why (and why not) should I use a metallic piston head?
How about a silent head set?
Is aluminum piston more durable?
Why (and why not) is the one o’clock gear timing an issue for Type I LPEG?
Can I still use the smaller batteries to power my upgraded mechbox?
I want to hide my battery inside the grip and the stock but the battery cells are too big. What should I do?
Chaining up your batteries: Parallel VS Serial configurations.
Should I use Sanyo battery cells for maximum performance?
Why (and why not) is it necessary to replace the stock wires?
Why is it necessary to shorten the wires?
Can I use stereo wires instead?
Why (and why not) is it necessary to replace the stock Tamiya connector?
Are NiCd batteries superior to NiMH batteries for driving upgraded mechbox?
What is wrong with the soda can test?
What is right with the soda can test?
What is the most accurate way to measure FPS?

<< High ROF Upgrade >>

What are the key elements of a high ROF setup?
Can I increase the ROF while keeping the FPS at the stock level by using 9.6V battery?
Voltage VS mah – which one matters the most?
Can I increase the ROF by replacing the mechanical contact switch with a solid state switching mechanism based on MOSFET?
Can I increase the ROF by using capacitors at the power source?
How can I increase the ROF while keeping the FPS at near-the-stock-level?
What is the right type of spring and battery to use for this purpose?

<< High Accuracy Upgrade >>

What are the key elements of a high accuracy setup?
Does a V-HopUp help?
How to improve accuracy with short barrel?
Can a long barrel deliver higher accuracy and range?
Why (and why not) should I replace the stock cylinder when using a longer inner barrel?
What is good about a high precision barrel?
How to maximize the effectiveness of a high precision barrel?
What is the drawback of using a high precision barrel?
What can cause the hopup rubber to break?
I have to wind my hop almost all the way up just to get flat flight. What is wrong?

<< be Tech plastic V3 mechbox series >>

Are the stock plastic gears durable enough?
Should I replace the plastic gears with metal gears?
Should I replace the stock cylinder set?
Can I mix and match TM piston with the stock cylinder?
How do I fix the fore grip wobble problem?
Can I use the TM high cap on it?
What is proper LPEG usage?

Free Sample of Airsoft Press AEG V2 Mechbox Upgrade Manual and AEG V3 Mechbox Upgrade Manual